Showing results: 3361 - 3375 of 4500 items found.
-
JTAG Technologies Inc.
Want to improve the overall test coverage of your assembled boards? It’s easy. Simply combine or integrate your JTAG Technologies boundary-scan tools with your existing automatic test equipment (ATE). We work with any vendor of in-circuit testers (ICT), flying probes (FPT) or functional testers (FT).We offer solutions for most of the available automatic test equipment systems, in addition we can support you with customized integrations for your existing automatic test equipment (ATE).
-
PXIe-1149.1/4E -
Corelis, Inc.
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
MOTOMEA
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
EE-120A-3S -
EMSYST Ltd
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
PTFM-1000V2 -
HORIBA, Ltd.
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
Wewon Environmental Chambers Co, Ltd.
Benchtop thermal forcing system from Wewon Environmental Chambers Co., Ltd. has a mini body structure and affordable machine price. The machine can test a wide temperature range, Since no compressor is required for refrigeration, so the benchtop temperature forcing unit’s energy consumption is very low. The repeated resistance degree of the tested sample in the instantaneous extremely high temperature and extremely low temperature continuous environment can detect the chemical changes and physical damage caused by thermal expansion and cold contraction of the sample in the shortest time, so as to achieve the goal of confirming the quality of the tested sample.https://www.wewontech.com/benchtop-thermal-forcing-system/
-
Entes Elektronik
LV power capacitors are circuit elements which compensate the inductive reactive loads on a system. Being able to connect and disconnect up to 100 times a day in accordance with load variations in automatic reactive power compensation systems really speaks for the quality and endurance and capacitors. Upon connection/disconnection instances, currents which have higher values than the nominal value may occur on reactive power compensation capacitors. ENTES ENT.C series power capacitors are designed to withstand the severe and poor conditions which may shorten the operating life during reactive power compensation. This endurance is the result of advanced engineering and long-term test procedures.
-
IPMT-3 -
FM SYSTEMS, INC.
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for meter test and calibration including portable power source, standard reference meter and meter test system. All products are accredited to the highest production standards with different options of measurement accuracy (class 0.05 and class 0.1).These enable them to cover different applications for test and calibration of different types of energy meters, electric transducers, indicating meters and so on.
-
MK Test Systems Ltd.
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
SYSTEM 8 (AICT) -
ABI Electronics Ltd
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
M5-2-COF -
Mark-10 Corp.
The M5-2-COF coefficient of friction (COF) gauge is an integral part of a COF testing system, typically including a motorized test stand and COF fixture. With a capacity of 2 lbF [10 N], the gauge can be used to measure friction for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients are displayed on the backlit LCD, and are calculated from a user-programmable sled weight.
-
4605-HTR -
TESEC, INC
4605-HTR is a MAP Sorter which picks up devices from wafer ring and sorts to tape or bin according to the MAP file created by film frame test handler or prober. 4605-HTR is a high speed handling system, available for 12 inches wafer rings. When used in combination with 4170-IH, 4605-HTR much improves efficiency in testing process of leadless devices as a high speed sorting machine.
-
60-106-002 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 60-106-002 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. It features remote control via USB or LXI Ethernet and this version of the chassis includes Scan List Sequencing & Triggering. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
AMETEK VTI Instruments
VTI is the first choice for mission critical applications or applications where the cost of test is high and failure is not an option. Applications include missile system testing and solid rocket motor testing. This is because our products are recognized in the industry for their reliability and are designed with built-in capabilities to maximize measurement confidence. Simply put, if you need equipment that is going to give you the results you need, contact us to get started.
